# How I Spent My Summer Vacation

**URL:** <https://59plymouth.net/t/how-i-spent-my-summer-vacation/3953>\
**Category:** Rebuilds\
**Created:** [September 1, 2025, 7:08pm UTC](https://59plymouth.net/t/how-i-spent-my-summer-vacation/3953 "2025-09-01T19:08:51Z")\
**Posts on this page:** 1\
**Showing post:** 4

<div class="post-metadata">

**Author:** ![Faulkner](https://59plymouth.net/user_avatar/59plymouth.net/faulkner/32/21944_2.png) [@Faulkner](https://59plymouth.net/u/Faulkner)\
**Post date:** [September 1, 2025, 7:31pm UTC](https://59plymouth.net/t/how-i-spent-my-summer-vacation/3953/4 "2025-09-01T19:31:58Z")

</div>

And for years, I’ve been without a working heater in Faulkner. Time to address that; I had installed a new heater valve, although the cable is not hooked up yet. And, I had two vacuum switches rebuilt, but were still sitting in the box.

 ![IMG_4233.JPEG](https://59plymouth.net/uploads/default/original/3X/3/d/3d44cd73059726b0a7337630750308fab0bb062e.jpeg)  
_I found the blower motor connector tucked behind the vent. This goes to the vacuum switch_

 ![IMG_4326.JPEG](https://59plymouth.net/uploads/default/original/3X/9/4/942fcf444dfdec35d5cedf021f9e42deba2aecbe.jpeg)  
_But very little else about the wiring made sense…_

 ![IMG_4237.JPEG](https://59plymouth.net/uploads/default/original/3X/8/4/842d759fd41ec4dbd02bb2ec9fc132965e496e42.jpeg)  
_…certainly, things were not connected as shown in the shop manual_

I determined that the power to the blower came not from the ignition switch, but from a spare tab on the temperature gauge (which in turn received power from the ignition switch). This wire was missing, so I made one.

On my original vacuum switch, the tubes were just plugged onto the nipples; fortunately, I have spare heater parts, and the plug that connects all the tubes at once to the nipples. When I finish the job, that will go on.

 ![IMG_4148.JPEG](https://59plymouth.net/uploads/default/original/3X/c/4/c4106c62a8d3417f05f7bd2bdcdf6ef07accd03d.jpeg)  
 ![IMG_4228.JPEG](https://59plymouth.net/uploads/default/original/3X/1/e/1e089e7f057d48e2a61a6a232b9d749eff85be49.jpeg)  
_I was able to remove all the buttons except for the bottom V(ent) through the face of the dash, but the lip of V caught on the dash. This will have to come out with the switch_

 ![IMG_4280.JPEG](https://59plymouth.net/uploads/default/original/3X/2/a/2a6f3451f02dbf7e120a44cff421c2ed596ccf91.jpeg)  
_I was able to twirl a 1/4" socket on the top and bottom screws into the vacuum switch plastic, that holds it to the bracket_

 ![IMG_4304.JPEG](https://59plymouth.net/uploads/default/original/3X/4/2/42d77b8c705cc871555078f686e548e9d20f149e.jpeg)  
_…and the switch is out! The rebuilt one went back in the same way_

 _I guess I got the wiring right! The two speed blower works perfectly_  

Things to do:

1. Test all the vacuum motors, using the siphon transfer pump discussed in [this thread](https://59plymouth.net/t/heater-vacuum-controls/2968/3). Unfortunately, the YouTube video on how to test them has disappeared, but I think I can figure it out. I have spare pots if any of them are non-functional.
2. Install the vacuum tube plug, and connect to the right vacuum motors (on the right side! 😲 ).
3. Run the vacuum line to the manifold.
4. Wire up the cable to the heater valve.

Thassit!

---

_[View the full topic](https://59plymouth.net/t/how-i-spent-my-summer-vacation/3953)._
