Faulkner gets a Redo



Works in progress. Or, whose progress has been completed!
User avatar
Faulkner
Posts: 3606
Joined: Sun Mar 07, 2004 6:59 pm
Location: Upper Darby, PA
Contact:

Re: Faulkner gets a Redo

Post by Faulkner » Tue Oct 09, 2018 6:13 pm

Michael's headed straight for the panhandle - I hope that by now, Dick, you are headed south to Palm Beach Gardens, and not still driving US 10. Send up a flare, will ya?!?

I think I'm going to go ahead and order those long J-bolts from Vans, on the likely prospect that your straps are not for a (rare) 23 gallon tank.
"If it's new, Image Plymouth's got it!"

User avatar
Dick Koch
Posts: 2130
Joined: Sat Jan 21, 2006 4:03 pm
Location: Palm Beach Gardens, Fl.
Contact:

Re: Faulkner gets a Redo

Post by Dick Koch » Tue Oct 09, 2018 6:34 pm

Just got home a couple of hours ago. Let me find the straps and get back to you.
Dick
Life is Beautiful! Sex, Beer & Mopars.

User avatar
Dick Koch
Posts: 2130
Joined: Sat Jan 21, 2006 4:03 pm
Location: Palm Beach Gardens, Fl.
Contact:

Re: Faulkner gets a Redo

Post by Dick Koch » Tue Oct 09, 2018 7:02 pm

Nope - Mine measure the same as yours. All you need is a coupling nut and a short piece of threaded rod. At my ACE we have coupling nuts up to 3/4" and threaded rod 3" and 6" long or longer.
Dick
Life is Beautiful! Sex, Beer & Mopars.

User avatar
Faulkner
Posts: 3606
Joined: Sun Mar 07, 2004 6:59 pm
Location: Upper Darby, PA
Contact:

Re: Faulkner gets a Redo

Post by Faulkner » Tue Oct 09, 2018 9:15 pm

Thanks Dick! I think if I were going to use a coupling nut, I would just use a bolt at the right length rather than all thread and a nut. But I ordered the longer J-bolts before I saw your reply, so let's see how I make out with those.

Glad to hear you are home safe and sound from "Cruisin' the Coast. Post some pix in "It's Show Time"!
"If it's new, Image Plymouth's got it!"

User avatar
Faulkner
Posts: 3606
Joined: Sun Mar 07, 2004 6:59 pm
Location: Upper Darby, PA
Contact:

Re: Faulkner gets a Redo

Post by Faulkner » Fri Oct 12, 2018 5:32 pm

There's a chance the J-bolts will arrive tomorrow. Meanwhile, some more tinkering in the engine compartment...

IMG_8044.JPG
I backed out the fitting and put in a close nipple, in hopes I could turn an elbow without having to remove the thermostat housing; no such luck
IMG_8047.JPG
So, off it came - here's everything back together
IMG_8050.JPG
Before I installed the recently rebuilt heater valve, I wired it closed - I need to rebuild the heater assembly under the dash, but I don't want to commit to that before Carlisle. There's enough gasket fragments to make a template for a replacement I'll make from a neoprene sheet
IMG_8051.JPG
Getting there! A busy day tomorrow, but maybe the radiator goes back in on Sunday
IMG_8048.JPG
What's the fitting for?


Oh yeah! What's this fitting for in the last pic? I seem to recall it from before, and wondering what - if anything - goes there. Is it for servicing? I don't think I had anything connected to it.
"If it's new, Image Plymouth's got it!"

User avatar
Faulkner
Posts: 3606
Joined: Sun Mar 07, 2004 6:59 pm
Location: Upper Darby, PA
Contact:

Re: Faulkner gets a Redo

Post by Faulkner » Sat Oct 13, 2018 4:56 pm

Rechromed. Rebuilt. Renewed!

bezels.jpg
"If it's new, Image Plymouth's got it!"

User avatar
Faulkner
Posts: 3606
Joined: Sun Mar 07, 2004 6:59 pm
Location: Upper Darby, PA
Contact:

Re: Faulkner gets a Redo

Post by Faulkner » Sun Oct 14, 2018 12:49 pm

(*Tap*, *Tap*...) Hey, is this mike on?!?

What's this fitting for?

fitting.JPG
"If it's new, Image Plymouth's got it!"

User avatar
Dick Koch
Posts: 2130
Joined: Sat Jan 21, 2006 4:03 pm
Location: Palm Beach Gardens, Fl.
Contact:

Re: Faulkner gets a Redo

Post by Dick Koch » Sun Oct 14, 2018 1:55 pm

It's the vacuum connection to the vacuum advance on the carburetor. This picture is from the 2 bbl. On the convert.
Dick
20181014_133834.jpg
Life is Beautiful! Sex, Beer & Mopars.

User avatar
Dick Koch
Posts: 2130
Joined: Sat Jan 21, 2006 4:03 pm
Location: Palm Beach Gardens, Fl.
Contact:

Re: Faulkner gets a Redo

Post by Dick Koch » Sun Oct 14, 2018 2:10 pm

This is a picture of Greenies 361 four barell carburetor, it's the vacuum connection to the vacuum advance.
Dick
20181014_140215.jpg
Life is Beautiful! Sex, Beer & Mopars.

User avatar
Faulkner
Posts: 3606
Joined: Sun Mar 07, 2004 6:59 pm
Location: Upper Darby, PA
Contact:

Re: Faulkner gets a Redo

Post by Faulkner » Sun Oct 14, 2018 5:02 pm

D'Oh! But of course. I have to hunt around in my stash of parts for that male fitting, and replace the rubber tubing. Here I was thinking this doodad - a thin little tube off of the rear vacuum line for the power brakes- was where the vac advance had been plugged into. But now I realize, that's for the dashboard heater control switch. I'll have to put a cap on that until I'm ready to redo the heater controls.

vacuum.jpg


I never got to hang the radiator today, but I did finish the power brake hoses and install the radiator core. In the process, I also managed to snap a bolt :o :shock: It's in an inconspicuous spot, and wouldn't be noticed - but it's bothering me now. I guess I'll drill it out... (*sigh*.) Nibbles of the elephant.

core.jpg
"If it's new, Image Plymouth's got it!"

User avatar
Dick Koch
Posts: 2130
Joined: Sat Jan 21, 2006 4:03 pm
Location: Palm Beach Gardens, Fl.
Contact:

Re: Faulkner gets a Redo

Post by Dick Koch » Sun Oct 14, 2018 7:30 pm

I would suggest that instead of rubber hose you use the white poly tubing, thats what is on Greenin and zero chance of collapsing. Can be sourced at ACE.
Dick
Life is Beautiful! Sex, Beer & Mopars.

Post Reply

Return to “Rebuilds”

Who is online

Users browsing this forum: No registered users and 1 guest