Search found 175 matches
- Sat Jul 02, 2016 8:01 pm
- Forum: Tech Support
- Topic: Oil leaking out of Vent tube??
- Replies: 3
- Views: 3424
Oil leaking out of Vent tube??
When I pulled my car out of the garage to day I noticed a stream of oil starting at a spot directly under where the valve cover vent pipe was located. there was probably about half pint of oil in all on the floor. the inside of my vent tube was saturated in oil. Any toughs? Is this even possible?
- Sun Jun 12, 2016 1:21 am
- Forum: Wanted
- Topic: Power Steering pump
- Replies: 3
- Views: 3466
Re: Power Steering pump
Thanks guys..you're the best
- Tue Jun 07, 2016 11:46 am
- Forum: Wanted
- Topic: Power Steering pump
- Replies: 3
- Views: 3466
Power Steering pump
Hey Guys, Looking for a power steering pump. thanks
- Thu May 26, 2016 10:49 am
- Forum: Tech Support
- Topic: Tire Pressure
- Replies: 3
- Views: 2959
Re: Tire Pressure
Thanks Guys, Ill try those things.
- Wed May 25, 2016 7:41 pm
- Forum: Tech Support
- Topic: Tire Pressure
- Replies: 3
- Views: 2959
Tire Pressure
I have been driving with the tire pressure at 24 psi as the manual instructs, but my tires look flat at 24 psi and I'm getting a lot of vibration at high speeds (65 mph). I tried increasing tire pressure to 32 psi, tires look closer to right but I'm still getting vibration. My question is what psi d...
- Sat May 21, 2016 1:27 pm
- Forum: Wanted
- Topic: wheel paint
- Replies: 8
- Views: 5738
Re: wheel paint
Thanks Guys
Lowering
Id like to lower the car a little with out permanently altering anything and with out blocks. What options do I have? I know the front can be adjusted with the torsion air but I don't know what to do with the back. Im hoping I can get some kind of after market de arched leaf springs that would fit. ...
- Sat May 21, 2016 12:36 pm
- Forum: How To
- Topic: door and hood alignment
- Replies: 6
- Views: 5703
Re: door and hood alignment
Thanks DickDick Koch wrote:The large 57/58 service manual has all the body alignment procedures starting on page 405. There should also be a technical booklet on the site with more information.
Good luck,
Dick
- Sat May 21, 2016 12:35 pm
- Forum: How To
- Topic: door and hood alignment
- Replies: 6
- Views: 5703
Re: door and hood alignment
There is a technical booklet on door alignment for the 57 but not for the 59. There isn't a lot of difference so it might work http://www.imperialclub.com/Repair/Lit/Master/110/index.htm And for the people who get bored on a rainy day here is the link to all the Master Service Technician Service bo...
- Sat May 21, 2016 12:35 pm
- Forum: How To
- Topic: door and hood alignment
- Replies: 6
- Views: 5703
Re: door and hood alignment
Here's the body section of the manual Dick is talking about: http://www.59plymouth.net/59gallery/albums/userpics/10003/5758-Part-3_Section-1_Body.pdf I'm sure there is a technical booklet that focuses on alignment procedures, but unfortunately it doesn't look like we have that one... But, give the ...
- Wed May 11, 2016 8:05 pm
- Forum: How To
- Topic: door and hood alignment
- Replies: 6
- Views: 5703
door and hood alignment
I need some advise on some alignment issues. Firstly... the rear driver side corner of my hood is about 1/4" lower than the fender, the front of the hood is fine. Can I just simply place a shim between the hood and hinge or do i need to a loosen the studs in the firewall and adjust the hinge pl...
- Sat Apr 16, 2016 11:13 am
- Forum: Wanted
- Topic: wheel paint
- Replies: 8
- Views: 5738
wheel paint
Are there any over the counter wheel paints available that is a close match to factory silver? Thanks
- Thu Mar 31, 2016 5:18 pm
- Forum: Wanted
- Topic: Air Filter Decal
- Replies: 2
- Views: 2746
Air Filter Decal
I've been looking, with out any success for a 59 mopar air filter decal. The oldest I can find is for a 62 which is very similar but not the same as the one on my car. So my plan is to make one with Photo Shop from whats left of the existing decal and then have a local print shop make me a sticker. ...
- Tue Feb 16, 2016 6:01 pm
- Forum: How To
- Topic: Trans Fluid
- Replies: 5
- Views: 4883
Re: Trans Fluid
Thanks John!
- Tue Feb 16, 2016 5:27 pm
- Forum: How To
- Topic: Seat Cover Removal
- Replies: 3
- Views: 3395
Re: Seat Cover Removal
How do I remove the rear bench? In my Cutlass there was two screws spread out across the bottom front of the bench. Would it be the same for the Fury? I wasn't able to see any exposed screws. Thanks in advance.